AirframeOctober 25, 2026· 11 min read

Aircraft Landing Gear, Wheels and Brakes: The A&P Exam Guide

Landing gear questions reward the mechanic who can name the part, explain what it does, and say what happens when it wears out. Configured for ATA chapter 32, this is the system that carries every landing load and every brake application, and the Airframe test treats it that way.

SL

SkyLicense Team

FAA A&P exam preparation specialists: helping mechanics earn their Airframe & Powerplant certificate since 2025

What AM.II.E Covers

Landing gear is Subject E of the Airframe section (AM.II) of the Aviation Mechanic ACS, known in maintenance as ATA chapter 32. The knowledge elements run from gear configuration and retraction through struts, wheels, tires, bearings, brakes and steering. The skills are hands on: service a strut, inspect a wheel and tire, adjust a brake. The Airframe written test is 100 questions in two hours at a 70 percent pass mark. See our ACS syllabus guide for the subject map.

Tricycle, Tailwheel, Fixed, Retractable

  • Tricycle. Mains aft of the center of gravity, nose wheel forward. Good visibility, but the nose gear takes steering and side loads.
  • Tailwheel. Mains forward, small wheel at the tail. Lighter and better on rough strips, but the center of gravity sits behind the mains, so directional control is the pilot’s job.
  • Fixed. Simple and light, often with fairings. Skis and floats are fixed variants.
  • Retractable. Hydraulic, electric or manual, with uplocks, downlocks, warning systems, and emergency extension by backup hydraulics, stored nitrogen or free fall.

A squat switch blocks retraction on the ground, a warning fires if the gear is not down and locked with power reduced, and the emergency system must work with the normal system failed. The actuation is in our hydraulic systems guide.

Shock Struts: The Air-Oil Oleo

An oleo strut holds hydraulic fluid below and dry nitrogen above. On touchdown the lower cylinder rises and forces oil through a metering orifice: the oil absorbs the energy, the nitrogen stores it and returns the strut to extension, while the metering pin shrinks the orifice through the stroke.

Service it by the manual: deflate, fill with the specified fluid to the level given for the stated strut position, charge with dry nitrogen, then measure the extension, often called the X dimension. Use nitrogen, never shop air: compressed air carries moisture that freezes at altitude and oxygen that feeds a fire.

Torque Links, Shimmy Dampers, Steering

Torque links, or scissors, tie the lower cylinder to the upper and carry steering torque while letting the strut stroke. Worn bushings or a loose link give axial play and shimmy, a rapid oscillation of the nose wheel about its steering axis. Causes are tire pressure, wheel balance, worn bushings, a loose steering collar and a damper low on fluid. The damper resists fast movement, so it suppresses oscillation but does not fix the wear behind it.

Wheels, Bearings, Preload

A wheel is two halves bolted together and sealed with an O ring, running tapered roller bearings in the hub. On a tubeless wheel the tire seals on the bead seat. Inspect for cracks at the bolt holes, corrosion in the bead area and worn bearing bores, and check bearings for spalling, brinelling and a rough feel when turned dry. Preload follows the manual: torque the axle nut while rotating the wheel to seat the bearings, back it off, then apply the specified preload or end play.

Tires: Bias and Radial, Tubes, Limits

A bias ply tire runs casing plies at opposing angles, for a stiff sidewall. A radial runs plies at 90 degrees to the tread centerline with a belt under the tread, so it runs cooler. Tires are certificated under TSO-C62, wheel and brake assemblies under TSO-C26. Tubeless is the modern norm; a tube type tire must match its wheel.

  • Wear. Tread grooves contain wear indicator bars. Tread worn to the bar is worn out.
  • Flat spots. From a skid before the wheel spins up. Shallow may be serviceable, cord showing is not.
  • Cuts and cord. Limits come from the manufacturer. A cut through cord, visible cord or a bulge from a separated ply removes the tire at once, and it may only be retreaded inside those limits.

Brake Types and Wear Indicators

  • Single disc. One steel disc keyed to the wheel, gripped by a caliper with pistons and lining pucks. Common on light aircraft.
  • Multiple disc. Rotating discs keyed to the wheel alternating with stationary discs keyed to a torque plate, for far more friction area.
  • Segmented rotor. Segments instead of one ring, so the rotor grows with heat without cracking.
  • Carbon. Carbon composite heat sink discs, lighter than steel for the same energy and able to run very hot. Wear is judged by the manufacturer’s pin or stack method.

The indicator is the quick check. On many light aircraft a pin in the lining backing plate moves outward as the lining wears, and when it reaches the disc the lining is due. Also check discs for scoring, heat checking and minimum thickness.

Brake Fluid, Parking Brake, Anti-Skid

Two mineral base specifications dominate: MIL-PRF-5606, a petroleum base fluid, and MIL-PRF-83282, a synthetic hydrocarbon with a much higher flash point and better fire resistance at the brake. Both are dyed red, so the label, not the color, tells you what is in the system. Automotive DOT fluid is glycol based and attacks seals in a mineral system. The parking brake traps line pressure with a valve, never set on hot brakes. Anti-skid modulates pressure from wheel speed transducers.

Inspection and Airworthiness

14 CFR 43.13(a) requires the methods in the manufacturer’s manual, or AC 43.13-1B where the manufacturer gives none. Chapter 9, Section 1 of AC 43.13-1B covers landing gear inspection, opening at paragraph 9-1. The annual or 100 hour inspection required by 14 CFR 91.409 uses the scope in Part 43 Appendix D, and paragraph (e) lists the gear group: units for condition and attachment, shock absorbing devices for improper oleo fluid level, linkages and trusses for wear, the retracting and locking mechanism, hydraulic lines for leakage, wheels, tires, and brake adjustment.

Airworthiness directives under Part 39 apply to specific part numbers, so paperwork is part of the job. Each inspection ends in a record entry under 14 CFR 43.9 and a return to service under 43.7. Our O&P exam guide covers how the exam grades that reasoning.

Start your FAA A&P exam preparation with SkyLicense free →

📥 Get the free printable study checklist: a 30-day FAA A&P exam prep plan with daily tasks covering 14 CFR Parts 43 and 65, AC 43.13-1B, ADs, and full-length exam simulations.

Download Free 30-Day Checklist →

Share this article

Want to check where you stand? Run a timed FAA A&P practice test — General, Airframe and Powerplant, timed exactly like the real exam, with an explanation citing the reference for every question.

FAA A&P practice test

Ready to train for your FAA A&P exam?

Exam-style questions, timed simulations and the theory for your General, Airframe and Powerplant ratings — pick your plan and start today. The FREE plan costs nothing.

Get Started

Create a free account