ExamsNovember 1, 2026· 9 min read

Aircraft Propellers: Fixed Pitch, Constant Speed and the A&P Exam

Propellers close out the Powerplant test, and they are where candidates answer with a pilot’s vocabulary instead of a mechanic’s. The exam wants blade angle, pitch definitions, the governor, and the rule that decides whether a damaged blade flies.

SL

SkyLicense Team

FAA A&P exam preparation specialists: helping mechanics earn their Airframe & Powerplant certificate since 2025

Where Propellers Sit on the Exam

Propellers are subject area AM.III.M of the Aviation Mechanic Powerplant ACS, ATA chapter 61. The Powerplant test is 100 questions in two hours with a 70 percent pass mark, and the propeller items reach into theory, blade design, hubs, governors, ice protection and inspection. Our exam structure guide covers the paper. The source text is FAA-H-8083-32B, Powerplant Handbook, Chapter 7.

Blade Nomenclature and Station Numbers

A blade has a face, the cambered thrust side, and a back. The leading edge meets the air, the trailing edge leaves it. The shank is the thick rounded section near the hub, the butt fits into the hub, and the tip is generally the last 6 inches. Blade stations are measured in inches from the center of the hub, so a twisted blade carries a different angle at every station while rotational velocity climbs toward the tip. Blade angle is checked at a stated station, usually 75 percent of the radius.

Pitch, Slip and Efficiency

Two definitions must be exact, because the test offers one as a distractor. Geometric pitch is the distance the propeller should advance in one revolution with no slippage. Effective pitch is the distance it actually advances, and slip is the difference between them. The handbook formula is geometric pitch equals 2 times pi times R times the tangent of the blade angle at the 75 percent station. Efficiency runs from about 50 to 87 percent depending on slip, and tip speed sets the ceiling: excessive tip speed costs efficiency and brings flutter, which is why propeller aircraft top out near 400 mph.

The Forces That Twist a Rotating Blade

Centrifugal force tries to pull it out of the hub, which is why blade weight drives hub design. Thrust bending bends the blade forward, torque bending bends it against rotation, and two twisting moments fight each other: aerodynamic twisting raises blade angle, centrifugal twisting lowers it, and centrifugal twisting wins. Some constant speed designs therefore let centrifugal twisting drive the blades toward low pitch while governor oil pressure drives them toward high pitch.

The Classifications

  • Fixed pitch. Angle set at manufacture, efficient at one combination of rpm and airspeed.
  • Ground adjustable. Set on the ground with shims or a blade clamp.
  • Controllable pitch. The pilot moves a valve and changes pitch directly, with no governing.
  • Constant speed. A governor holds the selected rpm and blade angle floats to absorb power changes.
  • Feathering. Blades drive to roughly 90 degrees so a dead engine stops producing drag.
  • Reversing and beta. Negative blade angle for braking; in beta the power lever sets blade angle directly, outside governor control.

Turboprops combine the last three. Our turbine engine guide covers the engine side of that pairing.

How the Governor Holds an RPM

The governor is an rpm sensor on top of a high pressure oil pump. Flyweights ride a rotating shaft and are opposed by the speeder spring, whose tension the cockpit control sets. At the selected rpm the flyweights balance the spring and the pilot valve stays in null. Raise the rpm, the flyweights fly outward and the valve releases oil from the propeller piston: blade angle rises, load increases and the engine slows back to the setting. Drop the rpm and the spring wins, the valve ports oil to the piston and pitch falls until rpm recovers. On most light aircraft the governor supplies oil for low pitch, so losing governor oil sends the blades toward high pitch or feather.

Construction, Damage and Repair Limits

Wood propellers are laminated blades on a wood hub, fabric covered near the tip with a metal tipping on the leading edge. Metal blades are forged and machined aluminum, some one piece with the hub. Stresses are highest near the hub, and a nick concentrates stress, so damage is not cosmetic. Inspect for nicks, dents, cracks, loose tipping, erosion, blade play and the grease trails that show a leaking hub seal.

Tracking, Balance and Vibration

Tracking compares tip positions in the same plane of rotation. AC 43.13-1B, Chapter 8, Section 6 gives 1/16 inch as the general tolerance between opposite blades, and a manufacturer tolerance governs where one exists. Out of track blades, unequal blade angles and imbalance are the usual causes. Static balance is done at overhaul on a stand; dynamic balance is done on the aircraft, where the handbook records Hartzell’s recommendation of 0.2 inches per second or less. Fix leaks and loose parts first, because no weight corrects a mechanical defect.

Part 43: Inspection, Major Repair, ADs

Appendix D, paragraph (h) lists the propeller group for an annual or 100 hour inspection: the propeller assembly for cracks, nicks, binds and oil leakage; bolts for improper torquing and lack of safetying; anti-icing devices for improper operation and obvious defects; control mechanisms for improper operation, insecure mounting and restricted travel. Methods come from 43.13(a): the manufacturer’s manual, or AC 43.13-1B where none is given.

Appendix A separates minor from major. Shortening blades, repairing or machining a steel hub, retipping a wood propeller, replacing tip fabric, repair of governors, overhaul of controllable pitch propellers, and repairs to deep dents or straightening an aluminum blade, are major repairs. An A&P who blends a shallow nick inside the manual limits performs minor repair; a deep dent goes to a repair station. A strike is its own case: Lycoming Service Bulletin 533C sets the sudden stoppage action, including crankshaft and gear inspection. ADs run by part and serial number, for example AD 2020-12-07, since superseded, which required eddy current inspections of certain Hamilton Sundstrand 54H blades.

Propeller items reward the candidate who can name the part, state which force acts on it, and quote the rule that limits it. The landing gear and brakes guide works the same way for the Airframe side, and the Powerplant FAQ covers the question patterns.

Start your FAA A&P exam preparation with SkyLicense free →

📥 Get the free printable study checklist: a 30-day FAA A&P exam prep plan with daily tasks covering 14 CFR Parts 43 and 65, AC 43.13-1B, ADs, and full-length exam simulations.

Download Free 30-Day Checklist →

Share this article

Want to check where you stand? Take a free FAA A&P practice test — General, Airframe and Powerplant, timed exactly like the real exam, with an explanation citing the reference for every question.

free FAA A&P practice test

Ready to train for your FAA A&P exam?

Exam-style questions, timed simulations and the theory for your General, Airframe and Powerplant ratings — pick your plan and start today. The FREE plan costs nothing.

Get Started

Create a free account